XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
54?/DIV>
Automatic DIP Switch Configurations
Each time the module assembly (XStream Module mounted to an XIB-R Interface Board) is
powered on, intelligence on t
Board sends AT Commands that program
the module based on positions
uring
er-on sequence affect
To avoid overwriting previous
(due to the automatic
configurations that take place
dule assembly is powered on), it is necessary to
disable a processor located on
rface board. To disable the processor, populate J7 of
the XIB-R Interface Board. By
Table燘02. Module燩owerup燨ption
he MaxStream Interface
of the DIP Switch. Automatic configurations that take place d
module parameter values as shown below.
ly stored custom configurations
the pow
each time the mo
the XIB-R inte
default, J7 jumper is not populated.
s?J7爅umper燼nd燙onfig燬witch)牋?/DIV>
Condition
Behavior
If J7 is popu
Processor is disable
lated
d and AT Commands are not sent to the Module.
If Config Switch is pressed
Processor is disabled and Module enters into AT Command Mode.
If J7 is NOT populated and Config Switch
is NOT pressed
Execute logic as shown in table below.
Table燘03. AT燙ommands燬ent燼s爎esult爋f燚IP燬witch燬ettings?SW?燚IP燬witch)牋?/DIV>
Condition
Behavior
Restore Default Parameter Values of the Module
If SW1 & SW2 are ON (up)
AT Commands sent: ATRE (Restore Defaults) Command
ATWR (Write) Command
Serial Interfacing Options
If SW1 is ON (up)
AT Commands sent: ATCS 0 (RS-232 Operation: CTS function for CTS line,
DB-9 pin 8)
ATCD 2 (DO3 - RX LED = low)
If SW1 is OFF (down)
AT Commands sent: ATCS 3 (RS-485 or RS-422 Operation)
ATCD 2 (DO3 - RX LED = low)
Parity Options
If SW5 & SW6 are OFF (down)
AT Commands sent: ATNB 0 (parity = none)
If SW5 is OFF (down) & SW6 is ON (up) AT Commands sent: ATNB 1 (parity = even)
If SW5 is ON (up) & SW6 is OFF (down) AT Commands sent: ATNB 2 (parity = odd)
If SW5 is ON (up) & SW6 is ON (up)
AT Commands sent: ATNB 5 (parity = 9th bit data over-the-air)
Exit AT Command Mode
Always
AT Commands sent: ATCN (Exit AT Command Mode)
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XIB-R
BOARD INTERFACE RS232/485
ZMN2400HPDB
BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B
KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC
IC TEMP SENSOR NI1000 SOT23-3
02110102-000
SNSR TILT RATIO 60DEG 500MA FLNG
1-5209285-2
FOPC BOA 12DB FC/UPC BP SM
2-1693560-0
BOA 20DB LC/UPC BB
517SS16
MAGNETIC SENSORS BIPOLAR ICS
相关代理商/技术参数
XIB-R
功能描述:界面模块 RS-232/485 interface 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIB-U
功能描述:界面模块 USB interface board 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIC25040
制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-080
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-081
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-082
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-083
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V